Effect of Al2O3 particles on mechanical and tribological properties of Al–Mg dual-matrix nanocomposites

This article aims to manufacture homogenous dual-matrix Al–Mg/Al₂O₃ nanocomposite from their raw materials and give insight into the correlation between powder morphology, crystallite structure and their mechanical and tribological properties. Al–Mg dual-matrix reinforced with micro/nano Al₂O₃ particles was manufactured by a novel double high-energy ball milling process followed by a cold consolidation and sintering. Microstructure and phase composition of the prepared samples were characterized using FE-SEM, EDS and XRD inspections. Mechanical and wear properties were characterized using compression and sliding wear tests. The results showed that a milling of Mg with Al₂O₃ particles in an initial step before mixing with Al has the beneficial of well dispersion of Al₂O₃ nanoparticles in Al–Mg dual matrix. The Al–Mg dual matrix reinforced with nano-size Al₂O₃ showed 3.29-times smaller crystallite size than pure Al. Moreover, the hardness and compressive strength are enhanced by adding nano-size Al₂O₃ with Al–Mg dual matrix composite while the ductility is maintained relatively high. Additionally, the wear rate of this composite was reduced by a factor of 2.7 compared to pure Al. The reduced crystallite size, the dispersion of Al₂O₃ nanoparticles and the formation of (Al–Mg)_ss were the main improvement factors for mechanical and wear properties.     

阴极保护技术在水工金属结构埋件上的应用

制作了水工金属结构埋件模型,研究不同种类牺牲阳极和外加电流方法对埋件的保护作用,以寻找切实可行的水工金属结构埋件长效保护方案。结果表明:采用牺牲阳极法进行阴极保护,当溶液电导率为2000μS/cm时,镁合金对水工金属结构埋件的保护距离可达到100cm,具有较好的保护效果;铝合金和锌合金由于表面钝化作用,对水工金属结构埋件起不到保护作用。恒电位极化方法可在不同电导率情况下对埋件起到较好的保护效果。     

海面油膜的偏振反射特性仿真实验

为了给海面溢油污染识别检测提供理论基础,根据菲涅尔反射公式的偏振反射系数,结合偏振双向反射率因子和粗糙海面的概率密度分布函数,建立了完善的pBRDF模型,仿真在不同太阳入射角度、不同探测器观测角度以及不同海面风速风向等条件下海水和油膜的偏振反射分布函数。结果表明:海水和油膜太阳天顶角为53°和56°时P偏振反射率分别为1.0×10^-5和2.5×10^-5,S偏振反射率随着太阳天顶角的增加而增加;海面风速越大偏振反射率峰值越小;海面风向只改变pBRDF的空间位置;海水和油膜线偏振度空间分布有明显差异。搭建实验平台相机以40°拍摄时,得出海水和油膜的线偏振度分别在0.2~0.4, 0.5~0.7之间,同时表明利用偏振探测获取目标场景的偏振度和偏振角图可提高图像质量。     

Perovskite SrFe1-xTixO3-δ (x < = 0.1) cathode for low temperature solid oxide fuel cell

Stable and compatible cathode materials are a key factor for realizing the low-temperature (LT, ≤600?°C) operation and practical implementations of solid oxide fuel cells (SOFCs). In this study, perovskite oxides SrFe_1-xTi_xO_3-δ (x?< = 0.1), with various ratios of Ti doping, are prepared by a sol-gel method for cathode material for LT-SOFCs. The structure, morphology and thermo-gravimetric characteristics of the resultant SFT powders are investigated. It is found that the Ti is successfully doped into SrFeO_3-δ to form a single phase cubic perovskite structure and crystal structure of SFT shows better stability than SrFeO_3-δ. The dc electrical conductivity and electrochemical properties of SFT are measured and analysed by four-probe and electrochemical impedance spectra (EIS) measurements, respectively. The obtained SFT exhibits a very low polarization resistance (R_p), .01 Ωcm² at 600?C. The SFT powders using as cathode in fuel cell devices, exhibit maximum power density of 551?mW?cm^?2 with open circuit voltage (OCV) of 1.15?V at 600?C. The good performance of the SFT cathode indicates a high rate of oxygen diffusion through the material at cathode. By enabling operation at low temperatures, SFT cathodes may result in a practical implementation of SOFCs.     

A Minimalist Single-Layer Metasurface for Arbitrary and Full Control of Vector Vortex Beams

Vector vortex beams (VVBs) possess ubiquitous applications from particle trapping to quantum information. Recently, the bulky optical devices for generating VVBs have been miniaturized by using metasurfaces. Nevertheless, it is quite challenging for the metasurface-generated VVBs to possess arbitrary polarization and phase distributions. More critical is that the VVBs' annular intensity profiles demonstrated hitherto are dependent on topological charges and are hence not perfect, posing difficulties in spatially shared co-propagation of multiple vortex beams. Here, a single-layer metasurface to address all those aforementioned challenges in one go is proposed, which consists of two identical crystal-silicon nanoblocks with varying positions and rotation angles (i.e., four geometric parameters throughout). Those four geometric parameters are found to be adequate for independent and arbitrary control of the amplitude, phase, and polarization of light. Perfect VVBs with arbitrary polarization and phase distributions are successfully generated, and the constant intensity profiles independent of their topological charges and polarization orders are demonstrated. The proposed strategy casts a distinct perception that a minimalist design of just one single-layer metasurface can empower such robust and versatile control of VVBs. That provides promising opportunities for generating more complex vortex field for advanced applications in structural light, optical micromanipulation, and data communication.     

Robust Linear Interpolation and Extrapolation of Stationary Time Series in Lp

To deal with uncertainty of the spectral distribution, we consider minimax interpolation and extrapolation problems in L^p for stationary processes. The interpolation and extrapolation problems can be regarded as a linear approximation problem on the unit disk in the complex plane. Although the robust one-step-ahead predictor and interpolator has already been considered separately in the previous literature, we give two conditions for the uncertainty class to find the minimax interpolator and extrapolator in the general framework from both the point of view of the observation set and the point of view of evaluation on the interpolation and extrapolation error under the L^p-norm. We show that there exists a minimax interpolator and extrapolator for the class of spectral densities ε-contaminated by unknown spectral densities under our conditions. When the uncertainty class contains spectral distribution functions which are not absolutely continuous to the Lebesgue measure, we show that there exists an approximate interpolator and extrapolator in L^p such that its maximal interpolation and extrapolation error is arbitrarily close to the minimax error when the spectral distributions have densities. Our results are applicable to the stationary harmonizable stable processes.     

Electrochemical determination of niobium cathode as an efficient electrocatalyst for hydrogen generation in acidic media

Hydrogen gas (H₂) is notified as a renewable energy carrier. It is wanted to discover a low-cost electrocatalyst for the hydrogen evolution reaction (HER) to substitute the high-cost Pt in electrolysis cell. Niobium electrocatalyst nominated to substitute noble materials for electrocatalytic H₂ production and its electrochemical manner was estimated in H₂SO₄ acid of various concentrations utilizing a steady-state polarization and electrochemical impedance spectroscopy (EIS). The influences of acid concentration, cathodic potential and temperature on the H₂ creation were examined. The outcomes display that HER on Nb electrode proceeds by the Volmer-Heyrovsky mechanism. EIS tests, under open circuit and under cathodic polarization, were performed and the fitting has been done utilizing a suggested model for the electrode/electrolyte interface. Apparent activation energies (E_a) were estimated to be ca. 10.5 kJ mol^?1 for the HER on Nb. Thus, Nb is a good electrocatalyst for the cathodic H₂ manufacturing.     

A Multiscale-Porous Anion Exchange Membrane for Convenient and Scalable Electrokinetic Concentration of Cationic Species

A device able to electrokinetically concentrate cationic samples has many potential medical and industrial applications, but until now has remained undeveloped due to the lack of a commercial anion-permselective material leading to a prohibitively complex fabrication procedure. Herein, a novel multiscale-porous anion exchange membrane (MP-AEM) that enables the convenient and scalable electrokinetic concentration of cationic species is proposed. A mechanically enhanced multiscale-porous structure with a solid framework is realized by adopting polyester resin as an additive to overcome the intrinsic limitations of the AEM material. The scalable MP-AEM-embedded electrokinetic concentrator is devised based on the peculiar properties of the MP-AEM that for allow both ion and fluid transport. With the MP-AEM, the concentrator is fabricated in a highly streamlined manner consisting only of a simple insertion and assembly. The concentration performance of the MP-AEM-embedded electrokinetic concentrator is demonstrated with a positively charged fluorescent dye and a fluorescein-labeled protein, and the results show enrichment factors of 250 and 500, respectively. The MP-AEM makes cationic electrokinetic concentration more accessible and scalable, thereby enabling further progress in a wide range of fields.     

溶解氧变化对阴极极化下10Ni5CrMo钢氢脆敏感性的影响

摘要：为研究溶解氧质量浓度对10Ni5CrMo钢在阴极极化条件下氢脆敏感性影响规律，对10Ni5CrMo钢进行了阴极极化下的电化学交流阻抗谱测试﹑并采用慢应变速率拉伸实验和断口分析方法研究了海水中溶解氧质量浓度变化和不同阴极极化下10Ni5CrMo钢的氢脆敏感性。结果表明：溶解氧质量浓度变化对10Ni5CrMo钢强度几乎没有影响；同一溶解氧质量浓度下，随极化电位负移，断裂时间、伸长率、断面收缩率明显降低，氢脆系数增加，氢脆敏感性显著提高，极化电位达到-1000mV时，氢脆系数已超过安全区允许的最高值25%，进入危险区；同一极化电位下，随着海水中溶解氧质量浓度减少，材料塑性变差，断裂时间、伸长率和断面收缩率不断降低，氢脆系数增加，氢脆敏感性提高。     

DP980高强钢连续退火后的组织与性能

研究了不同工艺参数对980 MPa级连续退火双相钢组织及力学性能的影响,利用光学显微镜、透射电镜(TEM)以及拉伸试验对双相钢的微观组织和力学性能进行测试及分析。结果表明:DP980钢的退火组织主要由铁素体、马氏体岛和少量的贝氏体组成,马氏体岛附近的位错密度较高。随着均热温度的升高,DP980钢的抗拉强度呈现先降低后升高的趋势,屈服强度与抗拉强度的趋势一致,伸长率先升高后降低。随着过时效温度的升高,DP980钢的抗拉强度和屈服强度降低,降低幅度较小,伸长率上升,但变化不明显,说明通过调整过时效温度来调控其力学性能的作用较小。